Product Code: #C1967662
Product Code: #C1967642
Product Code: #C1967653
Product Code: #C1967646
Product Code: #C1967648
Product Code: #C1967647
Product Code: #C1967652
Product Code: #C1967660
Product Code: #C1967663
Product Code: #C1978734
Product Code: #C2611225
Product Code: #C2611224
Product Code: #C1967661
Product Code: #C1978733
| GreenSpec® approved and helps contributes towards LEED credits, the XLERATOR Hand Dryer completely dries hands in 10 to 15 seconds. Sustainable Supply has the lowest wholesale distributor prices on the Internet for Xlerator hand dryers… guaranteed! Take advantage of 80% less energy consumption compared to conventional hand dryers and 95% cost savings compared to paper towels. Virtually maintenance free, Xlerator dryers come standard with a 5-year limited warranty with over a decade of proven performance. Xlerator dryers adhere to many green certifications including: LEED, GreenSpec, Greener Product, Green Business Bureau, Green Restaurant Association, Green Hotels Association, meets GSA requirements, and are made in the USA. For the lowest prices and fastest shipping on Excel hand dryers, choose Sustainable Supply today! |
FREE SHIPPING ON ALL XLERATOR DRYERS. Excel Xlerator hand dryers are endorsed by the Green Hotels and Green Restaurant Associations and are used in green buildings, schools, airports, stadiums, or any other high traffic restroom. By eliminating residual moisture, the hands are warm and comfortable after drying. This new energy efficient hand dryer technology rapidly dries hands in two sequential phases. In the first phase, loose water droplets are blown from the hands with a strong, controlled air blast. In the second phase, residual moisture is evaporated and the hands are warmed by an air stream heated up to 135 degrees F (55 degrees C).
Dimensions: 11 3/4" LG. X 12 11/16" HIGH X 6 11/16" DEEP
Weight: 16 LBS. (7.3 KGS.)
A. Cover shall be a one-piece, heavy-duty, rib-reinforced, die-cast zinc alloy or fiberglass re-enforced bulk molding compound (see product descriptions). It shall be lightweight, unbreakable, rustproof and all exposed surfaces shall be bright chrome plated or finished with chip-proof, electrostatically applied epoxy paint and fastened to a wall plate by two chrome plated tamper-proof bolts.
B. Wall plate shall be equipped with (3) 7/8" (22 mm) diameter holes, one of which shall be suitable for use with surface conduit, for ease of wiring.
C. All internal parts shall be coated according to Underwriters' Laboratories, Inc. requirements.
D. Entire mechanism shall be internally grounded
A. Motor shall be a series commutated through-flow discharge vacuum motor/blower (5/8 HP / 20,000 RPM) which provides air velocity of 16,000 LFM (linear feet per minute) at the air outlet and 14,000 LFM at the hands (4 inches [102 mm] below air outlet).
B. Heating element (900 W) is constructed of Nichrome wire and mounted inside the blower housing, thereby being vandal proof. It shall be protected by an automatic resetting thermostat, which shall open whenever air flow is cut off and shall close when flow of air is resumed. It shall produce an air temperature of up to 135°F (57°C) at a 72°F (22°C) ambient room temperature at the hands (4 inches [102 mm] below air outlet).
C. Control assembly is activated by an infrared optical sensor located next to the air outlet. The dryer shall operate as long as hands are under the air outlet. There is a 35-second lockout feature if hands are not removed.
The dryer shall be guaranteed to be free from defects for a period of three (3) years. Warranty shall include factory performed labor as well as the repair or exchange of defective parts, at manufacturer's option.
UNITS ARE AVAILABLE AS SPECIFIED IN: 110/120 Volt, 12.5 Amps, 60HZ